如何解决BUILDROOT+U-BOOT:“同步中止”处理程序,esr 0x96000210'错误
我正在使用 U-boot 为 S905x2 单元编译 Linux,但在成功编译刻录后,我在启动时收到“同步中止”处理程序,esr 0x96000210”错误。
完整的启动日志如下。
谁能告诉为什么会发生这种情况? 我正在使用 Libretech-cc-buildroot git repo。使用 Amlogic vendor U-boot(调整 fdtaddr 的大小,因为它太小了)。
我正在为 MINIMXIII II、S905x2 2G/16G 编译。
BL2 Built : 13:48:56,Sep 23 2016.
gxl g7459bd4 - jianxin.pan@droid06
set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 1
cpu clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from emmC,src: 0x0000c200,des: 0x01400000,size: 0x00004000
New fip structure!
Load bl30 from emmC,src: 0x00010200,des: 0x01100000,size: 0x0000d600
Load bl31 from emmC,src: 0x00020200,des: 0x10100000,size: 0x00015400
Load bl33 from emmC,src: 0x00038200,des: 0x01000000,size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21,Sep 20 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
e0 64 25 87 a7 56 28 f 21 20 68 3f [0.393512 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gdd4a4de (Mar 03 2017 - 18:35:08)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f500
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC,load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz,readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6,bus_timing=7,system=5.0ns
reset Failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect Failed and ret:fffffffe
nandphy_init Failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
Sdio Port B: 0,Sdio Port C: 1
emmc/sd response timeout,cmd8,status=0x1ff2800
emmc/sd response timeout,cmd55,status=0x1ff2800
[mmc_init] mmc init success
mmc read lba=0x14000,blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxl platform: p212 variant: 2g
dtb 0 soc: gxl plat: p212 vari: 1g
dtb 1 soc: gxl plat: p212 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed8270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000,blocks=0x2
mmc read lba=0x12002,blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
emmC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 6,table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxl platform: p212 variant: 2g
dtb 0 soc: gxl plat: p212 vari: 1g
dtb 1 soc: gxl plat: p212 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]Failed to get fb addr for logo
[OSD]use default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]load fb addr from dts
[OSD]Failed to get fb addr for logo
[OSD]use default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=5760,height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SaraDC open channel(0).
SaraDC channel(0) is 0x7 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card in
[mmc_init] mmc init success
Device: Sdio Port B
Manufacturer ID: 3
OEM: 3456
Name: ASTCTran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 29.5 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: Sdio Port B
Manufacturer ID: 3
OEM: 3456
Name: ASTCTran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 29.5 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
488 bytes read in 4 ms (119.1 KiB/s)
## Executing script at 01080000
[mmc_init] mmc init success
switch to partitions #0,OK
mmc0 is current device
reading amlogic/meson-gxl-s905x-libretech-cc-sdcard.dtb
25157 bytes read in 9 ms (2.7 MiB/s)
reading image
16716288 bytes read in 915 ms (17.4 MiB/s)
"Synchronous Abort" handler,esr 0x96000210
ELR: 77ed3564
LR: 77ed3558
x0 : 0000000077f72f80 x1 : 0000000000080000
x2 : 000000000105c000 x3 : 000000000105c000
x4 : 00000000000000a8 x5 : 0000000002080000
x6 : 0000000077f40148 x7 : 0000000000000044
x8 : 0000000000000001 x9 : 0000000000000000
x10: 000000000000000f x11: 0000000077f41c90
x12: 0000000000000000 x13: 0000000000000000
x14: 0000000000000000 x15: 0000000000000000
x16: 0000000000000000 x17: 0000000000000000
x18: 0000000073eb8e28 x19: 0000000077f72e40
x20: 0000000000000003 x21: 0000000073ed3288
x22: 0000000077f72000 x23: 0000000077f72e40
x24: 0000000000000000 x25: 0000000073ed3280
x26: 0000000077f66c70 x27: 0000000073ed32b0
x28: 0000000000000000 x29: 0000000073eb7a20
版权声明:本文内容由互联网用户自发贡献,该文观点与技术仅代表作者本人。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容, 请发送邮件至 dio@foxmail.com 举报,一经查实,本站将立刻删除。