STM32：模拟看门狗只触发一次中断 HAL_ADC_LevelOutOfWindowCallback 主要ADC 和 WDG 配置回调

如何解决STM32：模拟看门狗只触发一次中断 HAL_ADC_LevelOutOfWindowCallback 主要ADC 和 WDG 配置回调

问题

• 我是否需要在每次触发模拟看门狗时重置它？ 中断还是我的代码有错误？
• 如果我每次都需要重置它，我该怎么做？
• 是否有可以在回调中调用的 HAL 函数？

我的代码

主要

HAL_ADC_Start(&hadc2);

ADC 和 WDG 配置

static void MX_ADC2_Init(void){
  ADC_AnalogWDGConfTypeDef AnalogWDGConfig = {0};
  ADC_ChannelConfTypeDef sConfig = {0};

  /** Common config*/
  hadc2.Instance = ADC2;
  hadc2.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV4;
  hadc2.Init.Resolution = ADC_RESOLUTION_8B;
  hadc2.Init.ScanConvMode = ADC_SCAN_DISABLE;
  hadc2.Init.ContinuousConvMode = ENABLE;
  hadc2.Init.DiscontinuousConvMode = DISABLE;
  hadc2.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;
  hadc2.Init.ExternalTrigConv = ADC_SOFTWARE_START;
  hadc2.Init.DataAlign = ADC_DATAALIGN_RIGHT;
  hadc2.Init.NbrOfConversion = 1;
  hadc2.Init.DMAContinuousRequests = DISABLE;
  hadc2.Init.EOCSelection = ADC_EOC_SINGLE_CONV;
  hadc2.Init.LowPowerAutoWait = DISABLE;
  hadc2.Init.Overrun = ADC_OVR_DATA_OVERWRITTEN;
  if (HAL_ADC_Init(&hadc2) != HAL_OK)
  {
    Error_Handler();
  }
  /** Configure Analog WatchDog 1 */
  AnalogWDGConfig.WatchdogNumber = ADC_ANALOGWATCHDOG_1;
  AnalogWDGConfig.WatchdogMode = ADC_ANALOGWATCHDOG_SINGLE_REG;
  AnalogWDGConfig.HighThreshold = 64-1;
  AnalogWDGConfig.LowThreshold = 0;
  AnalogWDGConfig.Channel = ADC_CHANNEL_1;
  AnalogWDGConfig.ITMode = ENABLE;
  if (HAL_ADC_AnalogWDGConfig(&hadc2,&AnalogWDGConfig) != HAL_OK)
  {
    Error_Handler();
  }
  /** Configure Regular Channel
  */
  sConfig.Channel = ADC_CHANNEL_1;
  sConfig.Rank = ADC_REGULAR_RANK_1;
  sConfig.SingleDiff = ADC_SINGLE_ENDED;
  sConfig.SamplingTime = ADC_SAMPLETIME_1CYCLE_5;
  sConfig.OffsetNumber = ADC_OFFSET_NONE;
  sConfig.Offset = 0;
  if (HAL_ADC_ConfigChannel(&hadc2,&sConfig) != HAL_OK)
  {
    Error_Handler();
  }
}

回调

void HAL_ADC_LevelOutOfWindowCallback (ADC_HandleTypeDef * hadc){
    HAL_GPIO_TogglePin(GPIOB,GPIO_PIN_3);
}